Responsible for leading and directing the activities of other GSE mechanics. Also does the work of a mechanic as required.

Location: Cleveland-Hopkins International Airport (CLE) Schedule:  40 hours a week with two consecutive days off depending on the operational needs of the shop.  Hourly Rate: $34.00  Required:  Must possess mechanical tools and toolbox

MECHANICAL DUTIES

All duties listed under GSE 1,2 and 3. Leadership Training Advanced trouble shooting. The ability to operate diagnostic equipment. The ability to read schematics (electrical, air, hydraulic). Verify that vehicles and equipment can pass appropriate safety inspections. Maintain repair and service all aspects of all vehicles and equipment. Determines the need and extent of repair work required on vehicles and equipment based on
operator’s reports and testing equipment. Assist in instructing Mechanic 2 on work procedures applicable to their respective level.
Inspects and approves work of Mechanic 2. Performs other duties as assigned or requested. Completes required documentation and performs data entry. Lead GSE team in all aspects of GSE business group.

EQUIPMENT TYPES

All equipment types listed under GSE 1 and 2 Ground power unit AC/Heat cart Airstart Lower deck loader Main deck loader Hydrant cart (narrow and wide body) Refuel tanker (all size and fuel types) Deicers Cater truck Hi lift truck Hydrant truck Towbarless push back Transport trailer (fuel and cargo)

MINIMUM QUALIFICATIONS

Vocational/ Specialized Training. Experience operating diagnostic equipment. Certification from a recognized program, preferred. 5 years experience in automotive/ mechanical work. Requires a Valid Driver’s License.

GSE Lead Technician - Tool Requirements

1/2” DRIVE RATCHET SWIVEL SOCKETS (DEEP AND SHALLOW REQUIRED) BREAKER BAR EXTENSIONS 3”, 6” AND 12” STANDARD 3/8”-1 ½“ METRIC 14MM-24MM 6” IMPACT EXTENSION DEEP IMPACT SOCKETS ½”-1 ½” ADAPTOR ½” - ¾” WRENCHES COMBINATION WRENCHES ¼”-1 ½” METRIC COMBINATION WRENCHES 8MM-24MM ALLEN WRENCHES 1/16”-3/8” METRIC ALLEN WRENCHES 2MM-12MM CRECENT WRENCHES 8”,12”, 15”, AND 18” HAMMERS, CHISELS, PUNCHES BALL PEEN HAMMER 16 oz BALL PEEN HAMMER 32 oz. 4 POUND SLEDGE PUNCH AND CHISEL SET CENTER PUNCH MISC FILE SET THREAD CHASER 1/4” DRIVE RATCHET SWIVEL SOCKETS (DEEP AND SHALLOW REQUIRED) STANDARD 1/8”-9/16” EXTENSIONS 3” AND 6” METRIC 5MM-14MM 3/8” DRIVE RATCHET SWIVEL EXTENSIONS 3”, 6” AND 12” SOCKETS (DEEP AND SHALLOW REQUIRED) STANDARD 5/16”-1” METRIC 8MM-21MM SPARK PLUG SOCKETS 5/8” AND 13/16” SCREWDRIVERS and PRY BARS PHILLIPS HEAD SCREWDRIVERS #1, #2, #3 AND STUBBY STANDARD HEAD SCREWDRIVERS #1, #2, AND STUBBY PRY BARS 12”, 24”, AND 36” 1/2” DRIVE IMPACT GUN 3/8” DRIVE IMPACT GUN DIE GRINDER OSHA APPROVED AIR NOZZLE TIRE CHUCK 1/2” AIR DRILL 3/8” AIR DRILL 1/4” AIR RATCHET 3/8” AIR RATCHET PLIERS STANDARD PLIERS 8” NEEDLE NOSE PLIERS CHANNEL LOCKS 12” AND 15” BRAKE SPRING PLIERS WIRE STRIPPERS WIRE CRIMPERS WIRE CUTTERS DIAGNOL CUTTERS SLIP JAW PLIERS VICE GRIPS 7” ,10”, AND 12” JUMPER WIRES (2 SETS) TEST LIGHT 12 AND 24 VOLT DIGITAL VOLT METER (FLUKEMETER OR EQUIVELANT) FLASHLIGHT FEELER GUAGE SET SPARK PLUG GAPPING TOOL FUSE PULLERS-AUTOMOTIVE FUSE PULLERS-NON CONDUCTIVE A/C, HIGH VOLTAGE BRAKE ADJUSTING SPOONS TIRE PRESSURE GUAGE (UP TO 120 PSI) TIRE VALVE STEM/CORE TOOL O-RING PICK SET/SCRIBE INSPECTION MIRROR SNAP RING PLIERS SET TAPE MEASURE (25’) OIL FILTER WRENCHES (SMALL, LARGE) WIRE BRUSH GLOVES LARGE LOCKING ROLLAWAY TOOL BOX SMALL LOCKING ROAD BOX

PHYSICAL DEMANDS

The physical demands described here are representative of those that must be met by an
employee to successfully perform the essential functions of this job. Reasonable
accommodations may be made to enable individuals with disabilities to perform the essential
functions.

While performing the duties of this job, the employee is frequently required to stand; walk; sit;
use hands to finger, handle, or feel objects, tools, or controls; reach with hands and arms; climb
or balance; stoop, kneel, crouch, or crawl; and talk or hear. The employee must frequently lift
and/or move up to 25 pounds.

WORK ENVIRONMENT

The work environment characteristics described here are representative of those an employee
encounters while performing the essential functions of this job. Reasonable accommodations
may be made to enable individuals with disabilities to perform the essential functions.
While performing the duties of this job, the employee regularly works in outside weather
conditions.

The employee frequently works near moving mechanical parts and in high,
precarious places and is frequently exposed to fumes or airborne particles, risk of electrical
shock, and vibration. The employee is occasionally exposed to toxic or caustic chemicals. The
noise level in the work environment is usually very loud.